doc. Ing.

Zdeněk Hadaš

Ph.D.

FSI, ÚMTMB OM – docent

+420 54114 2893
hadas@fme.vutbr.cz

Odeslat VUT zprávu

doc. Ing. Zdeněk Hadaš, Ph.D.

Publikace

  • 2020

    MACHŮ, Z.; ŠEVEČEK, O.; HADAŠ, Z.; KOTOUL, M. Modeling of electromechanical response and fracture resistance of multilayer piezoelectric energy harvester with residual stresses. JOURNAL OF INTELLIGENT MATERIAL SYSTEMS AND STRUCTURES, 2020, roč. 31, č. 19, s. 2261-2287. ISSN: 1530-8138.
    Detail | WWW

  • 2019

    SMILEK, J.; HADAŠ, Z.; VETIŠKA, J.; BEEBY, S. Rolling mass energy harvester for very low frequency of input vibrations. MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2019, č. 125, s. 215-228. ISSN: 0888-3270.
    Detail | WWW

    HADAŠ, Z.; KŠICA, F.; RUBEŠ, O. Piezoceramic patches for energy harvesting and sensing purposes. European Physical Journal-Special Topics, 2019, roč. 228, č. 7, s. 1589-1604. ISSN: 1951-6355.
    Detail | WWW

    TOFEL, P.; MACHŮ, Z.; CHLUP, Z.; HADRABA, H.; DRDLÍK, D.; ŠEVEČEK, O.; MAJER, Z.; HOLCMAN, V.; HADAŠ, Z. Novel layered architecture based on Al2O3/ZrO2/BaTiO3 for SMART piezoceramic electromechanical converters. European Physical Journal-Special Topics, 2019, roč. 228, č. 7, s. 1575-1588. ISSN: 1951-6355.
    Detail | WWW

    RUBEŠ, O.; BRABLC, M.; HADAŠ, Z. Nonlinear vibration energy harvester: Design and oscillating stability analyses. MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2019, č. 125, s. 170-184. ISSN: 0888-3270.
    Detail | WWW

    ULIANOV, C.; HADAŠ, Z.; HYDE, P.; SMILEK, J. Novel Energy Harvesting Solutions for Powering Trackside Electronic Equipment. In Sustainable Rail Transport. Cham: Springer, 2019. s. 229-255. ISBN: 978-3-030-19519-9.
    Detail | WWW

    KŠICA, F.; HADAŠ, Z.; HLINKA, J. Integration and test of piezocomposite sensors for structure health monitoring in aerospace. MEASUREMENT, Journal of the International Measurement Confederation (IMEKO), 2019, roč. 147, č. 106861, s. 1-10. ISSN: 0263-2241.
    Detail | WWW

  • 2018

    RUBEŠ, O.; HADAŠ, Z. Design and Simulation of Bistable Piezoceramic Cantilever for Energy Harvesting from Slow Swinging Movement. In 2018 IEEE 18th International Power Electronics and Motion Control Conference (PEMC). Budapest, Hungary: IEEE, 2018. s. 664-668. ISBN: 978-1-5386-4198-9.
    Detail | WWW

    HADRABA, P.; HADAŠ, Z. Virtual Twin of The Multi-spindle Lathe for the Chatter Time-domain Analysis. In Proceedings of the 2018 18th International Conference on Mechatronics – Mechatronika (ME). Brno: Vysoké učení technické v Brně, 2018. s. 35-40. ISBN: 978-80-214-5543-6.
    Detail

    HADAŠ, Z.; SMILEK, J. Efficiency of vibration energy harvesting systems. In Energy Harvesting for Wireless Sensor Networks Technology, Components and System Design. Berlin/Munich/Boston: Walter de Gruyter GmbH, 2018. s. 45-64. ISBN: 9783110445053.
    Detail | WWW

    MACHŮ, Z.; ŠEVEČEK, O.; MAJER, Z.; HADAŠ, Z.; KOTOUL, M. Optimization of the electro-mechanical response of the multilayer piezoelectric energy harvester. In Proceedings of the 2018 18th International Conference on Mechatronics – Mechatronika (ME). 1. Brno: Brno University of Technolgy, 2018, 2018. s. 143-148. ISBN: 978-80-214-5543-6.
    Detail | WWW

    KŠICA, F.; HADAŠ, Z.; HLINKA, J. Application of piezoelectric sensors for structural health monitoring in aerospace. In 2018 5th IEEE International Workshop on Metrology for AeroSpace (MetroAeroSpace) Proceedings. Rome, Italy: Institute of Electrical and Electronics Engineers Inc., 2018. s. 596-601. ISBN: 978-1-5386-2473-9.
    Detail | WWW

    HADAŠ, Z.; JANÁK, L.; SMILEK, J. Virtual prototypes of energy harvesting systems for industrial applications. MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2018, roč. 110, č. 1, s. 152-164. ISSN: 0888-3270.
    Detail | WWW

    RUBEŠ, O.; TOFEL, P.; MACKŮ, R.; ŠKARVADA, P.; KŠICA, F.; HADAŠ, Z. Piezoelectric Micro-fiber Composite Structure for Sensing and Energy Harvesting Applications. In Proceedings of the 2018 18th International Conference on Mechatronics – Mechatronika (ME). 1. Brno: Brno University of Technolgy, 2018, 2018. s. 344-349. ISBN: 978-80-214-5543-6.
    Detail | WWW

    SMILEK, J.; HADAŠ, Z. Experimental evaluation of Tusi couple based energy harvester for scavenging power from human motion. In The 14th International Conference on Vibration Engineering and Technology of Machinery (VETOMAC XIV). MATEC Web of Conferences. 211. Lisbon, Portugal: EDP Sciences, 2018. s. 1-6. ISSN: 2261-236X.
    Detail | WWW

    KŠICA, F.; HADAŠ, Z. Prediction of position-dependent stability lobes based on reduced virtual model. In 14th International Conference on Vibration Engineering and Technology of Machinery, VETOMAC 2018 Proceedings. MATEC Web of Conferences. Lisbon, Portugal: EDP Sciences, 2018. s. 1-6. ISSN: 2261-236X.
    Detail | WWW

    RUBEŠ, O.; BRABLC, M.; HADAŠ, Z. Verified nonlinear model of piezoelectric energy harvester. In The 14th International Conference on Vibration Engineering and Technology of Machinery (VETOMAC XIV). MATEC Web of Conferences. 211. Lisbon, Portugal: EDP Sciences, 2018. s. 1-6. ISSN: 2261-236X.
    Detail | WWW

    HADRABA, P.; HADAŠ, Z. Multi Body Vibration Analysis of 3 Axis Slide for Mass Damper Design. In Engineering Mechynics 2018. Praha: Institute of Termomechanics AS, 2018. s. 281-284. ISBN: 978-80-86246-88-8.
    Detail

    MACHŮ, Z.; MAJER, Z.; ŠEVEČEK, O.; ŠTEGNEROVÁ, K.; HADAŠ, Z. Electro-mechanical analysis of a multilayer piezoelectric cantilever energy harvester upon harmonic vibrations. In MATEC Web of Conferences. MATEC Web of Conferences. 210. EDP Sciences, 2018. s. 1-6. ISSN: 2261-236X.
    Detail | WWW

    HADAŠ, Z.; SMILEK, J.; RUBEŠ, O. Energy harvesting from passing train as source of energy for autonomous trackside objects. In The 14th International Conference on Vibration Engineering and Technology of Machinery (VETOMAC XIV). MATEC Web of Conferences. 211. Lisbon, Portugal: EDP Sciences, 2018. s. 1-6. ISSN: 2261-236X.
    Detail | WWW

    BAI, Y.; TOFEL, P.; HADAŠ, Z.; SMILEK, J.; LOŠÁK, P.; ŠKARVADA, P.; MACKŮ, R. Investigation of a cantilever structured piezoelectric energy harvester used for wearable devices with random vibration input. MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2018, roč. 106, č. 106, s. 303-318. ISSN: 0888-3270.
    Detail | WWW

  • 2017

    SMILEK, J.; HADAŠ, Z. Improving power output of inertial energy harvesters by employing principal component analysis of input acceleration. MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2017, roč. 85, č. 1, s. 801-808. ISSN: 0888-3270.
    Detail | WWW

    HADAŠ, Z.; SMILEK, J.; RUBEŠ, O. Analyses of electromagnetic and piezoelectric systems for efficient vibration energy harvesting. In Proceedings of SPIE - The International Society for Optical Engineering. Proceedings of SPIE. 10246. Barcelona: SPIE, 2017. s. 1024619-1 (1024619-8 s.)ISBN: 9781510609938. ISSN: 0277-786X.
    Detail | WWW

    KŠICA, F.; HADAŠ, Z. Position-Dependent Response Simulation of Machine Tool Using State-Space Models. MM Science Journal, 2017, roč. December, č. 1, s. 2120-2127. ISSN: 1803-1269.
    Detail | WWW

    HADRABA, P.; HADAŠ, Z. Dynamic Analysis of Multispindle Lathe. In Mechatronics 2017 Recent Technological and Scientific Advances. Advances in Intelligent Systems and Computing. 1. Brno: Springer International Publishing, 2017. s. 321-329. ISBN: 978-3-319-65959-6. ISSN: 2194-5365.
    Detail | WWW

    RUBEŠ, O.; HADAŠ, Z. Designing, Modelling and Testing of Vibration Energy Harvester with Nonlinear Stiffness. In Proceedings of SPIE - The International Society for Optical Engineering. Proceedings of SPIE. 10246. Barcelona: SPIE, 2017. s. 102460W-1 (102460W-9 s.)ISBN: 9781510609938. ISSN: 0277-786X.
    Detail | WWW

    SMILEK, J.; JANÁK, L.; RUBEŠ, O.; HADAŠ, Z. Smart Skins for Structural Health Monitoring in Aerospace Applications. In Proceedings of the EASN Association Conference - 7th EASN International Conference. 7th EASN International Conference Proceedings. European Aeronautics Science Network, 2017. s. 59-65. ISSN: 2523-5052.
    Detail | WWW

    SMILEK, J.; HADAŠ, Z. Coil Optimization for Linear Electromagnetic Energy Harvesters with Non-uniform Magnetic Field. In Mechatronics 2017. Advances in Intelligent Systems and Computing. Brno: Springer, 2017. s. 735-742. ISBN: 9783319659596. ISSN: 2194-5357.
    Detail

    KŠICA, F.; VETIŠKA, J.; HADAŠ, Z. Methodology for predicting dynamic behaviour of machine tools based on a virtual model. In Engineering Mechanics 2017. Engineering mechanics 2014. 1. Svratka: Brno University of Technology, Faculty of Mechanical Engineering, Institute of Solid Mechanics, Mechatronics and Biomechanics, 2017. s. 534-537. ISBN: 978-80-214-5497-2. ISSN: 1805-8248.
    Detail

    JANÁK, L.; ANČÍK, Z.; HADAŠ, Z. THERMOELECTRIC GENERATORS FOR AEROSPACE APPLICATIONS: DEVELOPMENT EXPERIENCE AND FUTURE CHALLENGES. In Proceedings of the EASN Association Conference - 7th EASN International Conference. 7th EASN International Conference Proceedings. European Aeronautics Science Network, 2017. s. 898-905. ISSN: 2523-5052.
    Detail | WWW

  • 2016

    ŠUBRT, K.; HOUŠKA, P.; HADAŠ, Z. Nové řídicí jednotky Faulhaber MC50xx. Automa, 2016, roč. 2016, č. 8- 9, s. 66-67. ISSN: 1210-9592.
    Detail | WWW

    JANÁK, L.; HADAŠ, Z.; SMILEK, J. Reliability Assessment of Electromechanical Energy Harvesting Systems. In Proceedings of the 2016 17th International Conference on Mechatronics – Mechatronika (ME) 2016. Praha: Czech Technical University in Prague, 2016. s. 119-122. ISBN: 978-80-01-05882-4.
    Detail

    ŽÁK, J.; HUBÁLEK, J.; PRÁŠEK, J.; PEKÁREK, J.; SVATOŠ, V.; HADAŠ, Z.; DUŠEK, D. Circuits for the Charge Push-through Electronics: Power Efficient Signal Processing Inside the Artificial Cochlear Implant. In Eurosensors XXX conference proceedings. Procedia Engineering. Budapest: 2016. s. 1710-1713. ISSN: 1877-7058.
    Detail

    SMILEK, J.; CIESLAR, F.; HADAŠ, Z. Measuring Acceleration in the Area of Human Head for Energy Harvesting Purposes. In Proceedings of the 2016 17th International Conference on Mechatronics – Mechatronika (ME) 2016. 1. Praha: 2016. s. 85-90. ISBN: 978-80-01-05882-4.
    Detail

    KOVÁŘ, J.; MOURALOVÁ, K.; KŠICA, F.; KROUPA, J.; ANDRŠ, O.; HADAŠ, Z. Virtual Reality in Context of Industry 4. 0. In Mechatronika 2016. Praha: Czech Technical University in Prague, Faculty of Electrical Engineering, 2016. s. 1-7. ISBN: 978-80-01-05882- 4.
    Detail | WWW

    JANÁK, L.; ŠTETINA, J.; FIALA, Z.; HADAŠ, Z. Quantities and Sensors for Machine Tool Spindle Condition Monitoring. MM Science Journal, 2016, roč. 2016, č. December, s. 1648-1653. ISSN: 1805-0476.
    Detail | WWW

    HADAŠ, Z.; GARAMI, B. Mechatronic Model of Harmonic Drive System. In Proceedings of the 2016 17th International Conference on Mechatronics – Mechatronika (ME) 2016. 1. Praha: Czech Technical University in Prague, 2016. s. 273-278. ISBN: 978-80-01-05882-4.
    Detail

    RUBEŠ, O.; SMILEK, J.; BRABLC, M.; HADAŠ, Z. Nonlinear Redesign of Vibration Energy Harvester: Linear Operation Test and Nonlinear Simulation of Extended Bandwidth. In 2016 IEEE International Power Electronics and Motion Control Conference (PEMC). Varna, Bulgaria: The Institute of Electrical and Electronics Engineers, 2016. s. 737-742. ISBN: 978-1-5090-1797-3.
    Detail | WWW

    SMILEK, J.; JANÁK, L.; HADAŠ, Z. Modular Multidisciplinary Models for Prototyping Energy Harvesting Products. In Recent Global Research and Education: Technological Challenges. Advances in Intelligent Systems and Computing. Berlín: Springer, 2016. s. 395-401. ISBN: 978-3-319-46489-3. ISSN: 2194-5357.
    Detail | WWW

    HADAŠ, Z.; VETIŠKA, V.; VETIŠKA, J.; KREJSA, J. Analysis and efficiency measurement of electromagnetic vibration energy harvesting system. Microsystem Technologies, 2016, roč. 22, č. 7, s. 1767-1779. ISSN: 0946-7076.
    Detail | WWW

    SMILEK, J.; HADAŠ, Z. A study of kinetic energy harvesting for biomedical application in the head area. Microsystem Technologies, 2016, roč. 22, č. 7, s. 1535-1547. ISSN: 0946-7076.
    Detail

    ŽÁK, J.; HADAŠ, Z.; DUŠEK, D.; PEKÁREK, J.; SVATOŠ, V.; JANÁK, L.; PRÁŠEK, J.; Hubálek, J. The Charge Push-Through Electronics Design for Fully Implantable Artificial Cochlea Powered by Energy Harvesting Technologies. Microsystem Technologies, 2016, roč. 22, č. 7, s. 1709-1719. ISSN: 0946-7076.
    Detail | WWW

  • 2015

    JANÁK, L.; ANČÍK, Z.; VETIŠKA, J.; HADAŠ, Z. Thermoelectric Generator Based on MEMS Module as an Electric Power Backup in Aerospace Applications. Materials Today: Proceedings, 2015, roč. 2, č. 2, s. 865-870. ISSN: 2214-7853.
    Detail

    KOTEK, L.; HOLUB, M.; VETIŠKA, J.; HADAŠ, Z.; BLECHA, P. Non-invasive displacement measurement of lightweight structures under dynamic excitations. In ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE). American Society of Mechanical Engineers (ASME), 2015. s. 5-11. ISBN: 978-0-7918-4648-3.
    Detail

    DUŠEK, D.; HADAŠ, Z.; PEKÁREK, J.; SVATOŠ, V.; ŽÁK, J.; PRÁŠEK, J.; HUBÁLEK, J. Design of an Artificial Microelectromechanical Cochlea. In Mechatronics Systems and Materials VI. Solid State Phenomena. Pfaffikon, Switzerland: Trans Tech Publications, 2015. s. 345-348. ISBN: 978-3-03835-227-3. ISSN: 1662-9779.
    Detail

    ŽÁK, J.; HADAŠ, Z.; PEKÁREK, J.; DUŠEK, D.; SVATOŠ, V.; JANÁK, L.; PRÁŠEK, J. Model-based design of artificial zero power cochlear implant. MECHATRONICS, 2015, roč. 31, č. NA, s. 30-41. ISSN: 0957-4158.
    Detail | WWW

    PROCHÁZKA, P.; PAZDERA, I.; CIPÍN, R.; HADAŠ, Z. Optimal Design Techniques for Small Electric Car Operating in Common Urban Traffic. Przeglad Elektrotechniczny, 2015, roč. 2015, č. 5, s. 1-8. ISSN: 0033-2097.
    Detail | WWW

    SVATOŠ, V.; PEKÁREK, J.; DUŠEK, D.; ŽÁK, J.; HADAŠ, Z.; PRÁŠEK, J. Design and Fabrication of Fully Implantable MEMS Cochlea. In Proceeedings of DAAAM International Symposium on Intelligent Manufacturing and Automation 2014. Energy Procedia. Vienna: Elsevier, 2015. s. 1224-1231. ISBN: 978-3-901509-99-5. ISSN: 1876-6102.
    Detail | WWW | Plný text v Digitální knihovně

    HADAŠ, Z.; VETIŠKA, V.; SMILEK, J.; ANDRŠ, O.; SINGULE, V. Efficiency of electromagnetic vibration energy harvesting system. In Proc. SPIE 9517, Smart Sensors, Actuators, and MEMS VII; and Cyber Physical Systems. Proceedings of SPIE. Bellingham, Washington, USA: SPIE, 2015. s. 95171H (95176H s.)ISBN: 9781628416442. ISSN: 0277- 786X.
    Detail | WWW

    SMILEK, J.; HADAŠ, Z. Assessment of MEMS energy harvester for medical applications. In Proc. SPIE 9517, Smart Sensors, Actuators, and MEMS VII; and Cyber Physical Systems. Proceedings of SPIE. Bellingham, Washington, USA: SPIE, 2015. s. 95170N (95177N s.)ISBN: 9781628416442. ISSN: 0277-786X.
    Detail | WWW

    ŽÁK, J.; HADAŠ, Z.; DUŠEK, D.; PEKÁREK, J.; SVATOŠ, V.; JANÁK, L.; PRÁŠEK, J. Design of the Charge Push- Through Electronics for Fully Implantable Artificial Cochlea. In Bio-MEMS and Medical Microdevices II, Proc. of SPIE. Proceedings of SPIE. 9518. Bellingham, Washington 98227- 0010 USA: SPIE, 2015. s. 95180P- 1 (95180P-9 s.)ISBN: 9781628416411. ISSN: 0277- 786X.
    Detail

    VETIŠKA, J.; HADAŠ, Z.; HOLUB, M. Multidisciplinary Multi- Body Modeling of Machine Tools. In Engineering mechanics 2015 - extended abstracts. 2015. s. 344-345. ISBN: 978-80-86246-42- 0.
    Detail

    ŠTETINA, J.; BŘEZINA, T.; HADAŠ, Z. Dynamic Analysis of Mechatronic System with Ball Screw. ENGINEERING MECHANICS 2015 21st International Conference Engineering Mechanics 2015. Engineering mechanics 2014. 1. Svratka: Institute of Theoretical and Applied Mechanics, Academy of Science of the Czech Republic, 2015. s. 292-293. ISBN: 978-80-86246-42- 0. ISSN: 1805- 8248.
    Detail | WWW

    ŠUBRT, K.; HOUŠKA, P.; HADAŠ, Z. Přesnost polohování s motorem Piezo LEGS. Automa, 2015, roč. 2015, č. 8- 9, s. 64-65. ISSN: 1210- 9592.
    Detail | WWW

    HADAŠ, Z.; ONDRŮŠEK, Č. Nonlinear spring-less electromagnetic vibration energy harvesting system. European Physical Journal-Special Topics, 2015, roč. 224, č. 14-15, s. 2881-2896. ISSN: 1951-6355.
    Detail

    HADAŠ, Z.; LÁN, R. Modelling and Verification of Piezoelectric Vibration Energy Harvester. In Advanced Mechatronics Solutions. Advances in Intelligent Systems and Computing. Switzerland: Springer International Publishing Switzerland, 2015. s. 305-310. ISBN: 978-3-319-23921-7. ISSN: 2194-5357.
    Detail

    VETIŠKA, V.; HADAŠ, Z.; HYNČICA, O.; ONDRŮŠEK, Č. Autonomous Monitoring Unit of Fault Condition with Vibration Energy Harvester. In Environment and Electrical Engineering (EEEIC), 2015 IEEE 15th International Conference on. Řím: 2015. s. 980-985. ISBN: 978-1-4799-7993-6.
    Detail | WWW

    JANÁK, L.; HADAŠ, Z. Machine Tool Health and Usage Monitoring System: An Initial Analyses. MM Science Journal, 2015, roč. 2015, č. December, s. 794-798. ISSN: 1803-1269.
    Detail | WWW

  • 2014

    HADAŠ, Z.; VETIŠKA, V.; HUZLÍK, R.; SINGULE, V. Model-based design and test of vibration energy harvester for aircraft application. Microsystem Technologies, 2014, roč. 20, č. 4-5, s. 841-843. ISSN: 0946-7076.
    Detail

    HOLUB, M.; HADAŠ, Z.; BLECHA, P.; VETIŠKA, J.; SINGULE, V. ENERGY ANALYSIS OF ENERGY HARVESTING FROM MACHINE TOOL VIBRATIONS. MM Scinece Journal, 2014, roč. 2014, č. March, s. 462-465. ISSN: 1805- 0476.
    Detail

    BŘEZINA, T.; BŘEZINA, L.; MAREK, J.; HADAŠ, Z.; VETIŠKA, J. SIMULATION ASSESSMENT OF SUPPRESSION OF MACHINE TOOL VIBRATIONS. In Engineering mechanics 2014. 1. 2014. s. 104-107. ISBN: 978-80-214-4871-1.
    Detail

    JANÁK, L.; HADAŠ, Z. Power Management Electronics for Thermoelectric Energy Harvesting Systems. ERIN 2014. Brno: Brno University of Technology, 2014. s. 34-34. ISBN: 978-80-214-4931- 2.
    Detail

    JANÁK, L.; HADAŠ, Z.; ANČÍK, Z.; KOPEČEK, P. Simulation of Power Management Electronics and Energy Storage Unit for MEMS Thermoelectric Generator. In Proceedings of the 11th European Conference on Thermoelectrics. Switzerland: Springer International Publishing, 2014. s. 189-195. ISBN: 978-3-319-07331- 6.
    Detail | WWW

    TOMAN, J.; SINGULE, V.; HADAŠ, Z. Model of Aircraft Actuator with BLAC Motor. In 16th INTERNATIONAL POWER ELECTRONICS AND MOTION CONTROL CONFERENCE AND EXPOSITION (PEMC 2014). 1. Antalya: Gazi University, Turkey, 2014. s. 278-283. ISBN: 978-1-4799-2060- 0.
    Detail | WWW

    HADAŠ, Z.; VETIŠKA, J. Energy Harvesting Analysis of Body Motion as Energy Source for Biomedical Devices. In Engineering mechanics 2014. Engineering mechanics 2014. 1. Brno: Brno University of Technology & IT AS CR, 2014. s. 204-207. ISBN: 978-80-214-4871-1. ISSN: 1805-8248.
    Detail

    ANDRŠ, O.; KOVÁŘ, J.; HADAŠ, Z. Introduction to Design of Speed Controller for Fuel Pump. In Proceedings of the 16th International Conference on Mechatronics – Mechatronika 2014. 1. Brno: VUT v Brně, 2014. s. 672-676. ISBN: 978-80-214-4817- 9.
    Detail

    KOTEK, L.; HOLUB, M.; VETIŠKA, J.; ŠUBRT, K.; HADAŠ, Z.; BLECHA, P. Comparison of Suitability of Tracking Marks for Optical Measurement of Displacement. In Proceedings of the 16th International Conference on Mechatronics – Mechatronika 2014. 1. Brno: Brno University of Technology, 2014. s. 489-493. ISBN: 978-80-214-4817- 9.
    Detail | WWW

    ŠTETINA, J.; BŘEZINA, T.; VETIŠKA, J.; HADAŠ, Z. Multibody Model of Heavy Machine Tool. In Proceedings of the 16th International Conference on Mechatronics – Mechatronika 2014. 1. Brno: Brno University of Technology, 2014. s. 266-270. ISBN: 978-80-214-4817- 9.
    Detail | WWW

    HADAŠ, Z.; KŠICA, F. Model- based Design of Testing Electromagnetic Shaker with Flexible Beam. In Proceedings of the 16th International Conference on Mechatronics – Mechatronika 2014. 1. Brno: Brno University of Technology, 2014. s. 393-398. ISBN: 978-80-214-4817- 9.
    Detail | WWW

    RUBEŠ, O.; SMILEK, J.; HADAŠ, Z. Development of Vibration Energy Harvester Fabricated by Rapid Prototyping Technology. In Proceedings of the 16th International Conference on Mechatronics – Mechatronika 2014. 1. Brno: Brno University of Technology, 2014. s. 178-182. ISBN: 978-80-214-4817- 9.
    Detail | WWW

    ANČÍK, Z.; HADAŠ, Z.; VLACH, R.; JANÁK, L.; SINGULE, V.; PROCHÁZKA, P. Simulation Modelling of MEMS Thermoelectric Generator for Aircraft Applications. In 16th INTERNATIONAL POWER ELECTRONICS AND MOTION CONTROL CONFERENCE AND EXPOSITION (PEMC 2014). 1. Antalya: Gazi University, Turkey, 2014. s. 265-270. ISBN: 978-1-4799-2060- 0.
    Detail | WWW

  • 2013

    HADAŠ, Z.; ANDRŠ, O.; VETIŠKA, V.; ANČÍK, Z. ENERGY HARVESTING TECHNOLOGIES FOR SPECIAL APPLICATIONS. In Proceedings of the International Conference on Military Technologies 2013 (ICMT'13). 1. Brno: University of Defence, 2013. s. 173-181. ISBN: 978-80-7231-917- 6.
    Detail

    HADAŠ, Z.; VETIŠKA, V.; ANČÍK, Z.; ONDRŮŠEK, Č.; SINGULE, V. Development of energy harvester system for avionics. In Proceedings of SPIE Smart Sensors, Actuators, and MEMS VI. 8763. Bellingham, Washington, USA: SPIE, 2013. s. 87631F- 1 (87631F-8 s.)ISBN: 978-0-8194-9560- 0.
    Detail

    ANČÍK, Z.; VLACH, R.; JANÁK, L.; KOPEČEK, P.; HADAŠ, Z. Modeling, simulation and experimental testing of the MEMS thermoelectric generators in wide range of operational conditions. In Proceedings of SPIE Smart Sensors, Actuators, and MEMS IV. 8763. Bellingham, Washington, USA: SPIE, 2013. s. 87631M- 1 (87631M-10 s.)ISBN: 9780819495600.
    Detail

    BŘEZINA, T.; BŘEZINA, L.; MAREK, J.; HADAŠ, Z.; VETIŠKA, J. Simulation Assessment of Suspension of Tool Vibrations during Machining. In Mechatronics 2013 Recent Technological and Scientific Advances. 1. Springer, 2013. s. 273-282. ISBN: 978-3-319-02294- 9.
    Detail

    DUŠEK, D.; HADAŠ, Z.; PEKÁREK, J.; SVATOŠ, V.; ŽÁK, J.; HUBÁLEK, J.; PRÁŠEK, J. Design of Artificial Microelectromechanical Cochlea. 2013.
    Detail

    JANÁK, L.; ANČÍK, Z.; HADAŠ, Z. Simulation Modelling of MEMS Thermoelectric Generators for Mechatronic Applications. In MECHATRONICS 2013: RECENT TECHNOLOGICAL AND SCIENTIFIC ADVANCES. Springer, 2013. s. 265-271. ISBN: 978-3-319-02294- 9.
    Detail

    ANDRŠ, O.; HADAŠ, Z.; KOVÁŘ, J.; VETIŠKA, J.; SINGULE, V. Model-Based Design of Mobile Platform with Integrated Actuator – Design with Respect to Mechatronic Education. In MECHATRONICS 2013: RECENT TECHNOLOGICAL AND SCIENTIFIC ADVANCES. 1. Springer, 2013. s. 891-988. ISBN: 978-3-319-02294- 9.
    Detail

    DUŠEK, D.; SVATOŠ, V.; PEKÁREK, J.; ŽÁK, J.; HADAŠ, Z.; PRÁŠEK, J.; HUBÁLEK, J. Research of low power full implantable microelectromechanicalcochlear implant. Espoo: Aalto university, 2013.
    Detail

    HADAŠ, Z.; HUZLÍK, R. FEM Model of Electro- magnetic Vibration Energy Harvester. In Mechatronics 2013: Recent Technological and Scientific Advances. Springer, 2013. s. 371-377. ISBN: 978-3-319-02294- 9.
    Detail

  • 2012

    HADAŠ, Z.; KURFÜRST, J.; ONDRŮŠEK, Č.; SINGULE, V. Artificial intelligence based optimization for vibration energy harvesting applications. Microsystem Technologies, 2012, roč. 18, č. 7- 8, s. 1003-1014. ISSN: 0946- 7076.
    Detail

    VETIŠKA, J.; HADAŠ, Z. Using of Simulation Modelling for Developing of Active Damping System. In 2012 INTERNATIONAL SYMPOSIUM ON Power Electronics, Electrical Drives, Automation and Motion. Sorrento: 2012. s. 1199-1204. ISBN: 978-1-4673-1300- 1.
    Detail

    BŘEZINA, T.; HADAŠ, Z.; VETIŠKA, J. Simulation Behavior of Machine Tool on the Base of Structural Analysis in Multi- Body System. In Proceedings of 15th International Conference on Mechatronics – Mechatronika 2012. 1. Praha: Czech Technical University in Prague, 2012. s. 347-350. ISBN: 978-80-01-04987- 7.
    Detail

    HADAŠ, Z.; BŘEZINA, T.; ANDRŠ, O.; VETIŠKA, J.; BŘEZINA, L. SIMULATION MODELLING OF MECHATRONIC SYSTEM WITH FLEXIBLE PARTS. In 15th International Power Electronics and Motion Control Conference and Exposition, EPE- PEMC 2012 ECCE Europe. 1. Novi Sad, Serbia: EPE- PEMC Council, 2012. s. LS2e.1- 1 (LS2e.1-7 s.)ISBN: 978-1-4673-1971- 3.
    Detail

    HADAŠ, Z.; VETIŠKA, J.; JURIGA, J. Stability Analysis of Cutting Process Using of Flexible Model in ADAMS. In Proceedings of 15th International Conference on Mechatronics – Mechatronika 2012. 1. Praha: Czech Technical University in Prague, 2012. s. 5-10. ISBN: 978-80-01-04987- 7.
    Detail

    HADAŠ, Z.; VETIŠKA, V.; SINGULE, V.; ANDRŠ, O.; KOVÁŘ, J.; VETIŠKA, J. Energy Harvesting from Mechanical Shocks Using A Sensitive Vibration Energy Harvester. International Journal of Advanced Robotic Systems, 2012, roč. 2012, č. 9, s. 1-7. ISSN: 1729- 8806.
    Detail

  • 2011

    HADAŠ, Z.; ONDRŮŠEK, Č.; KURFÜRST, J.; SINGULE, V. Vibration energy harvester optimization using artificial intelligence. In Microtechnologies for the New Millennium 2011 (Proceedings Volume 8066-8069). Proceedings of SPIE. 8066. 1000 20TH ST, PO BOX 10, BELLINGHAM, WA 98227- 0010 USA: SPIE- INT SOC OPTICAL ENGINEERING, 2011. s. 1-12. ISBN: 9780819486554. ISSN: 0277-786X.
    Detail

    BŘEZINA, T.; HADAŠ, Z.; VETIŠKA, J. Using of Co-simulation ADAMS- SIMULINK for Development of Mechatronic Systems. In PROCEEDINGS OF 14th INTERNATIONAL CONFERENCE ON MECHATRONICS. Trenčín: AD University of Trencin, 2011. s. 59-64. ISBN: 978-80-8075-476- 1.
    Detail

    BŘEZINA, T.; VETIŠKA, J.; HADAŠ, Z. SIMULATION MODELLING OF MACHINE TOOLS WITH FLEXIBLE PARTS AS MECHATRONIC SYSTEM. In Proceedings of the International Conference on Advances in Mechatronics 2011 (AIM 11). 1. Brno: Expertia o.p.s., 2011. s. 99-104. ISBN: 978-80-7231-848- 3.
    Detail

    HADAŠ, Z.; SINGULE, V. ENERGY HARVESTING – OPPORTUNITY FOR FUTURE REMOTE APPLICATIONS. In Engineering Mechanics 2011. 1. Praha: Academy of sciences of the Czech Republic, v.v.i., 2011. s. 167-170. ISBN: 978-80-87012-33- 8.
    Detail

    BŘEZINA, T.; ANDRŠ, O.; BŘEZINA, L.; HADAŠ, Z.; HOUŠKA, P.; KOVÁŘ, J.; VETIŠKA, J. VIRTUAL DESIGN OF INDUSTRIAL MANIPULATOR USING MECHATRONIC APPROACH. In Proceedings of the International Conference on Advances in Mechatronics 2011 (AIM 11). 1. Brno: Expertia o.p.s., 2011. s. 105-110. ISBN: 978-80-7231-848- 3.
    Detail

    BŘEZINA, T.; VETIŠKA, J.; HADAŠ, Z.; BŘEZINA, L. Simulation Modelling and Control of Mechatronic Systems with Flexible Parts. In Mechatronics Recent Technological and Scientific Advances. Berlin: Springer, 2011. s. 569-578. ISBN: 978-3-642-23243- 5.
    Detail

  • 2010

    HADAŠ, Z.; ONDRŮŠEK, Č.; SINGULE, V. Power sensitivity of vibration energy harvester. Microsystem Technologies, 2010, roč. 16, č. 5, s. 691-702. ISSN: 0946- 7076.
    Detail

    SINGULE, V.; HADAŠ, Z. Elektrické mikropohony v medicínské technice. Automa, 2010, roč. 16, č. 4, s. 48-49. ISSN: 1210- 9592.
    Detail

    BŘEZINA, T.; HADAŠ, Z.; SINGULE, V.; BLECHA, P. European Projects for Support of Mechatronic Fields at Brno University of Technology. In Proceedings of 13th international symposium on mechatronics, Mechatronika 2010. Trenčín: AD University of Trencin, 2010. s. 109-111. ISBN: 978-80-8075-476- 1.
    Detail

    HADAŠ, Z.; VĚCHET, S.; SINGULE, V.; ONDRŮŠEK, Č. Development of Energy Harvesting Sources for Remote Applications as Mechatronic systems. In PROCEEDINGS OF 14TH INTERNATIONAL POWER ELECTRONICS AND MOTION CONTROL CONFERENCE (EPE-PEMC 2010). Ohrid: 2010. s. 13-19. ISBN: 978-1-4244-7854- 5.
    Detail

    HADAŠ, Z.; SINGULE, V. New Subject Energy Harvesting for Education of Mechatronics. In Proceedings of 13th international symposium on mechatronics, Mechatronika 2010. Trenčín: AD University of Trencin, 2010. s. 16-17. ISBN: 978-80-8075-476- 1.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. Verification of Vibration Power Generator Model for Prediction of Harvested Power. Solid State Phenomena, 2010, roč. 2010, č. 164, s. 291-296. ISSN: 1012-0394.
    Detail

  • 2009

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. Optimal Design of Vibration Power Generator for Low Frequency. Solid State Phenomena, 2009, roč. 2009, č. 147- 149, s. 426-431. ISSN: 1012- 0394.
    Detail

    HADAŠ, Z.; SINGULE, V. ENERGY HARVESTING DEVICES AS MECHATRONIC SYSTEMS. In Book of Abstracts 12th International Conference on Mechatronics Mechatronika 2009. 1. Trenčín: AD University of Trenčín Faculty of Mechatronics, 2009. s. 3-7. ISBN: 978-80-8075-394- 8.
    Detail

    HADAŠ, Z.; ONDRŮŠEK, Č.; KURFÜRST, J. Optimization of Vibration Power Generator Parameters Using Self- Organizing Migrating Algorithm. In Recent Advancecs in Mechatronics 2008- 2009. 1. Berlin: Springer- Verlag Berlin Heidelberg, 2009. s. 245-250. ISBN: 978-3-642-05021- 3.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. VERIFICATION OF VIBRATION POWER GENERATOR MODEL FOR PREDICTION OF HARVESTED POWER. In The 5th International Conference Mechatronic Systems and Materials. 1. Vilnius: VilniusTechnika, 2009. s. 27-29. ISBN: 978-9955-28-493- 2.
    Detail

    HADAŠ, Z.; ONDRŮŠEK, Č.; SINGULE, V. Increasing Sensitivity of Vibration Energy Harvester. Proceedings of SPIE, 2009, roč. 7362, č. 1, s. 1-8. ISSN: 0277- 786X.
    Detail

  • 2008

    HADAŠ, Z.; ZOUHAR, J. APPLICATION OF RAPID PROTOTYPING METHOD FOR DEVELOPMENT OF MECHATRONIC SYSTEMS. In Engineering Mechanics 2008. 1. Prague: Institute of Termomechanics, Academy of Sciences of the Czech Republic, 2008. s. 80-81. ISBN: 978-80-87012-11- 6.
    Detail

    HADAŠ, Z.; ONDRŮŠEK, Č.; SINGULE, V.; KLUGE, M. Vibration Power Generator for Aeronautics Applications. In Proceedings of the EUSPEN 10th anniversary international conference Volume I - Volume II. 1. Zurich: Copy & Druck Wein, 2008. s. 46-50. ISBN: 978-0-9553082-5- 3.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. UNIQUE WAYS OF GENERATING ENERGY FROM SURROUNDINGS AS AUTONOMOUS SOURCES OF ELECTRICAL ENERGY. In International conference on "Low Voltage Electrical Machines". 1. Šlapanice u Brna: Vysoké učení technické v Brně, Fakulta elektrotechniky a komunikačních technologií, Ústav výkonové elektrotechniky a elektroniky, 2008. s. 21-22. ISBN: 978-80-214-3795- 1.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. Optimal Design of Vibration Power Generator for Low Frequency. The 4th International Conference Mechatronic Systems and Materials. 1. Bialystok: Bialystok Technical University Press, 2008. s. 137-137.
    Detail

    HADAŠ, Z.; ZOUHAR, J.; SINGULE, V.; ONDRŮŠEK, Č. Design of Energy Harvesting Generator Base on Rapid Prototyping Parts. In 2008 13th Power Electronics and Motion Control Conference. 1. Poznan, POLAND: 2008. s. 1688-1692. ISBN: 978-1-4244-1741- 4.
    Detail

  • 2007

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. Simulation of Vibration Generator Non- linear Model. In Dynamics of Machines 2007. 1. Praha: Ústav termomechaniky AV ČR, 2007. s. 71-76. ISBN: 978-80-87012-03- 01.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. Simullation Modeling of Electromagetic Vibration Power Generator. In Engineering Mechanics 2007. 1. Prague: Institute of Termomechanics, Academy of Sciences of the Czech Republic, 2007. s. 71-72. ISBN: 978-80-87012-06- 2.
    Detail

    HADAŠ, Z. Mikrogenerátor jako mikromechanická soustava. Brno: VUTIUM, 2007.
    Detail

    BŘEZINA, T.; SINGULE, V.; HADAŠ, Z. Mechatronics Implementation Methodology At New Products Development And Design. In AiM 2007. 1. Brno: Expertia o.p.s., 2007. s. 1-18. ISBN: 978-80-7231-314- 3.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č.; KLUGE, M. Simulation of Vibration Power Generator. In Recent Advances in Mechatronics. 1. Berlin Heidelberg: Springer, 2007. s. 350-354. ISBN: 978-3-540-73955- 5.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č.; KLUGE, M. SIZE MATCHING OF VIBRATION POWER GENERATOR. In 16th International Conference on Electrical Drivesand Power Electronics. 1. 2007. s. 1-5. ISBN: 978-80-8073-867- 9.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. Development of Vibration Power Generator for Aeronautic Application. In Simulation Modelling of Mechatronic Systems III. Mechatronika. 2007. s. 83-100. ISBN: 978-80-214-3559- 9.
    Detail

    HADAŠ, Z.; KLUGE, M.; SINGULE, V.; ONDRŮŠEK, Č. Electromagnetic Vibration Power Generator. In 6th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics and Drivers. 1. Cracow, POLAND: IEEE, 2007. s. 451-455. ISBN: 978-1-4244-1061- 3.
    Detail

  • 2006

    SINGULE, V., HADAŠ, Z., ONDRŮŠEK, Č. OVERALL TUNING UP OF VIBRATION GENERATOR AND CHOICE OF ENERGY TRANSDUCER CONSTRUCTION. In Advanced Engineering Design 2006. Prague: Orgis s.r. o, 2006. s. 1 ( s.)
    Detail

    SINGULE, V.; HADAŠ, Z.; ONDRŮŠEK, Č. ANALYSIS OF GENERIC ENERGY HARVESTING VIBRATION GENERATOR. In 5th Conference on Advanced Engineering Design. 1. Prague: Orgis s.r. o, 2006. s. 1 ( s.)
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. OPTIMAL DESIGN OF VIBRATION GENERATOR FUNCTION PRODUCT AND VERIFICATION OF MODEL. In Simulation Modelling of Mechatronic Systems II. Mechatronika. 2006. s. 85-97. ISBN: 80-214-3341- 8.
    Detail

    SINGULE, V.; HADAŠ, Z.; ONDRŮŠEK, Č. ANALYSIS OF VIBRATION POWER GENERATOR. In ENGINEERING MECHANICS 2006. 2006. s. 328 ( s.)ISBN: 80-86246-27- 2.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. TUNING UP PARAMETERS OF VIBRATION GENERATOR. In Engineering Mechanics 2006. Svratka, Česká Republika: Academy of Sciences of the Czech Republik, 2006. s. 84 ( s.)ISBN: 80-86246-27- 2.
    Detail

  • 2005

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. The comparison and assessment of different conception of vibration microgenerator construction. In ENGINEERING MECHANICS 2005. Svratka, Česká Republika: Fakulta strojního inženýrství, VUT v Brně, 2005. s. 101 ( s.)ISBN: 80-85918-93- 5.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. Design and Simulating Modelling of Vibration Microgenerator. In Simulation Modelling of Mechatronic Systems I. Mechatronika. Brno: Brno University of Technology, Faculty of Mechanical Engineering, 2005, 2005. s. 143 ( s.)ISBN: 80-214-3144- X.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. MECHANISM OF VIBRATION MICROGENERATOR BASED ON NON- LINEAR STIFFNESS. Inženýrská mechanika - Engineering Mechanics, 2005, roč. 12, č. A1, s. 19 ( s.)ISSN: 1210- 2717.
    Detail

    HADAŠ, Z.; SINGULE, V.; ONDRŮŠEK, Č. The Comparison of the Simulation Results of the Vibration Microgenerator Model with the Measuring of the Vibration Microgenerator Prototype. In International Symposium on Electrical Machines SME 2005. 1. Opole, Polsko: Oficyna Widawnicza Politechniky Opolskiej, 2005. s. 419 ( s.)ISBN: 83-88492-74- 8.
    Detail

  • 2004

    HADAŠ, Z., SINGULE, V. Design of a vibraton microgenerator. In 2nd International PhD Conference on Mechnical Engineering - PhD2004. Plzeň: Faculty of Mechanical Engineering, Department of Machine Design, Západočeská Universita v Plzni, 2004. s. 31 ( s.)ISBN: 80-7043-330- 2.
    Detail

    HADAŠ, Z., SINGULE, V. Studie realizovatelnosti vibračního mikrogenerátoru. In Proceedings of the 7th International Symposium "Topical Questions of Teaching Mechatronics". Bratislav, SK: Slovak University of Technology Bratislava, Faculty of Mechanical Engineering CA MECHATRONICS, 2004. s. 26 ( s.)ISBN: 80-227-2064- X.
    Detail

    HADAŠ, Z., SINGULE, V. The design of a vibraton microgenerator. In "Low Voltage Electrical Machines" Joint Czech - Polish Conference on Project GACR 102/ 038013. Brno: Faculty of Electrical Engineering and Communication, Brno University of Technolgy; Department of Electrical Machines and Devices Silesian University of Technology, Gliwice, 2004. s. 33 ( s.)ISBN: 80-214-2632- 2.
    Detail

*) Citace publikací se generují jednou za 24 hodin.