Course detail

Processing and Digitizing of Analog Signals

FEKT-BZDAAcad. year: 2015/2016

The course deals with challenges of the design of analog circuits for processing signals from sensors including presentation of tools for simulation and analysis of electronic circuits, data acquisition, signal processing, and hardware resources for the practical design of electronic circuits. Students will learn basic signal conditioning circuits for active and passive sensors - the use of bridges, current sources, amplifiers and filters. Further, electronic circuitry for resistive, capacitive and inductive sensors, conditioning and processing of signals from thermocouples, photodiodes and sensors with piezoelements are analyzed in detail. Sensors with current loop output, mixed and isolated interface, and circuits for digitization of analog signals including specific sensors with digital output are also considered.

Learning outcomes of the course unit

The student is able to design independently and realize practically the basic electronic circuit for signal conditioning and processing from sensors of the most commonly measured physical quantities, he can also describe basic procedures for collecting and processing data using virtual instrumentation. He can identify specific circuit design for each type of physical transducers and apply it to a theoretical design. He is able to analyze basic circuit solution for processing signals from sensors with operational amplifiers with computer support in the Multisim environment. He can control the simulation environment and use fundamental analysis to determine and verify the properties of the solved electronic circuit. He can describe development platform NI Elvis and can use it to prototype design and verification of electronic circuit with basic electronic components and operational amplifiers. He can test created electronic circuit and compare the results with the simulation model and illustrate the basic static and dynamic parameters of the circuit (operating point, frequency response, etc.). He is able to describe common electrical interfaces of sensors and explain the basic principles of A/D converters used in electronic circuits of sensors of physical quantities.

Prerequisites

The student who enrolls this course should be able to explain principle of operation of basic passive and active electronic components, define their general parameters and use them in basic electronic circuits. He should also be able to list basic laws and rules for solving linear electronic circuits and use them. He should define the basic transmission parameters of passive two-ports, calculate and illustrate their frequency characteristics. He should explain the principle of simple operational amplifier and illustrate its basic internal structure. He should be able to enumerate basic types of A/D converters and describe the functional principle of D/A converters. He should be able to define a measurement system based on virtual instrumentation and describe the basic possibility of creating such a system using LabVIEW environment. Student should have such language skills to understand some educational materials in English.

Co-requisites

Not applicable.

Recommended optional programme components

Not applicable.

Recommended or required reading

KESTER, W. Practical design techniques for sensor signal conditioning. Analog Devices, Inc., USA, 1999. ISBN 0-916550-20-6. (EN)
PUNČOCHÁŘ, J. Operační zesilovače v elektronice. BEN - technická literatura, Praha, 5. vydání, 2002. 288 s. ISBN 80 7300-058-X. (CS)
JURÁNEK, A. MultiSIM - Elektronická laboratoř na PC. BEN - technická literatura, Praha, 1. vydání, 2008. 288 s. ISBN 978-80 7300-194. (CS)
SHEINGOLD, D. H. Transducer Interfacing Handbook - A Guide to Analog Signal Conditioning. Analog Device, Inc., USA, 1. vydání, březen 1980. 231 s. ISBN 0 916550-05-2. (EN)
KABEŠ, K. Operační zesilovače v automatizační technice. SNTL - Nakladatelství technické literatury n. p. Praha, 1. vydání, 1989. 260 s. (CS)
KŘIŠŤAN, L., VACHALA, V. Příručka pro navrhování elektronických obvodů. SNTL - Nakladatelství technické literatury n. p. Praha, 1. vydání, 1982. 400 s. (CS)
KITCHON CH., COUNTS, L. A Designer's Guide to Instrumentation Amplifiers. Analog Devices, Inc., USA, 2. vydání, 2004. 108 s. Dostupné z . (EN)
WILLIAMS, J. Application Note 43 - Bridge Circuits. Linear Technology, USA, červen 1990. 48 s. Dostupné z . (EN)
VLACH, J., HAVLÍČEK, J., VLACH, M. Začínamé s LabVIEW. BEN - technická literatura, Praha, 1. vydání, 2008. 248 s. ISBN 978-80 7300-245-9. (CS)
HOROWITZ, P., HILL, W. The art of electronics. Cambridge University Press, UK, 2. vydání, 1989 (2001). 1125 s. ISBN 0 521-37095-7. (EN)

Planned learning activities and teaching methods

Techning methods include lectures and practical laboratories.

Assesment methods and criteria linked to learning outcomes

Up to 40 points for the laboratory exercises in the following composition:
- up to 5 points (2+3) for two short practical tasks in the Multisim environment,
- up to 5 points (2+3) for two short practical tasks when using the NI Elvis platform,
- up to 10 points for test of theoretical knowledge related to operation of simulation, development and prototype software tools for electronic circuit design, signal acquisition and processing,
- up to 10 points from an individual theoretical design of electrical circuit involving simulation in Multisim,
- up to 10 points from practical realization and evaluation of parameters of electrical circuit using NI Elvis platform.
To get course-unit credit and the possibility to access the final exam at least half points from laboratory exercises is required, i.e. 20 points.
Up to 60 points for the written exam.

Language of instruction

Czech, English

Work placements

Not applicable.

Course curriculum

1. Introduction to the design of analog circuits for processing signals from sensors.
2. Tools for simulation and analysis of electronic circuits. MultiSIM. Software tools for data acquisition and data processing. LabVIEW.
3. Hardware and software tools for practical design of electronic circuits and analog and digital signals acquisition. NI ELVIS.
4. Sensors of nonelectrical quantities considered as electronic circuit components (active, passive).
5. Circuits for sensor signal conditioning - use of bridges, current sources, amplifiers and filters.
6. Amplifiers (operational, instrumentation, charge). Bridge sensor circuits (resistive, capacitive, inductive).
7. Passive sensors - circuitry for temperature and position sensors. Sensors with high impedance.
8. Passive sensors II - circuitry for resistance strain, force, pressure and flow sensors.
9. Active sensors - circuitry for thermocouples, photodiodes.
10. Active sensors II - circuitry for sensor position, velocity and acceleration.
11. Current loop, mixed and isolated interface.
12. Converters for digitization of analog signals.
13. Sensors with digital interface (I2C, SPI, etc.).

Aims

The main aim of the course is to get basic theoretical and practical skills for unaided design of analog circuits, especially for processing signals from sensors. Get practical experience with software for theoretical design and simulation of analog circuits, hardware and software resources for processing and digitization of analog signals from sensors and basic methods for processing and analysis of measured data.

Specification of controlled education, way of implementation and compensation for absences

Mandatory participation in laboratory exercises, in case of absence the exercise work can be supplemented with alternative exercise in same week or with a self-study of additional literature. Two excused absences are tolerated.

Classification of course in study plans

  • Programme EEKR-B Bachelor's

    branch B-AMT , 3. year of study, winter semester, 6 credits, optional specialized

  • Programme EEKR-CZV lifelong learning

    branch ET-CZV , 1. year of study, winter semester, 6 credits, optional specialized

Type of course unit

 

Lecture

26 hours, optionally

Teacher / Lecturer

Laboratory exercise

39 hours, compulsory

Teacher / Lecturer