Detail publikace

Empirical correlation for spray half cone angle in plain-jet airblast atomizers

Originální název

Empirical correlation for spray half cone angle in plain-jet airblast atomizers

Anglický název

Empirical correlation for spray half cone angle in plain-jet airblast atomizers

Jazyk

en

Originální abstrakt

Plain-jet airblast atomizers are widely used in industrial applications. The literature contains numerous papers on Sauter mean diameter, however, there is no estimation method available for spray cone angle, SCA, which derivation is the primary goal of this study. Four distinct, practical model liquids were analyzed: distilled water, diesel oil, light heating oil, and crude rapeseed oil. The atomizing pressure and liquid preheating temperature were varied in the range of 0.3–2.4 bar and 25–85 °C, respectively. This latter parameter enabled a wide and continuous liquid kinematic viscosity investigation range of 0.33–44.2 mm2/s. The resulting sprays were imaged at various shutter speeds for proper edge detection. An adaptive thresholding algorithm was developed in Matlab software environment to calculate SCA. The methodology is discussed in detail to facilitate the re-implementation of this technique since there is no generally accepted method for SCA measurement. SCA inversely varied with liquid density and followed a power law with the air-to-liquid mass flow ratio; however, the derived expression also performed well by replacing air-to-liquid mass flow ratio by either Mach number or momentum flux ratio. A simple empirical equation was derived, which allows the estimation of SCA of airblast atomization in a wide parameter range within a 3.5% deviation. The measured results were evaluated in the light of high-speed camera images in the vicinity of the nozzle; it was found that increased liquid jet breakup length decreases SCA while intense ligament formation increases it.

Anglický abstrakt

Plain-jet airblast atomizers are widely used in industrial applications. The literature contains numerous papers on Sauter mean diameter, however, there is no estimation method available for spray cone angle, SCA, which derivation is the primary goal of this study. Four distinct, practical model liquids were analyzed: distilled water, diesel oil, light heating oil, and crude rapeseed oil. The atomizing pressure and liquid preheating temperature were varied in the range of 0.3–2.4 bar and 25–85 °C, respectively. This latter parameter enabled a wide and continuous liquid kinematic viscosity investigation range of 0.33–44.2 mm2/s. The resulting sprays were imaged at various shutter speeds for proper edge detection. An adaptive thresholding algorithm was developed in Matlab software environment to calculate SCA. The methodology is discussed in detail to facilitate the re-implementation of this technique since there is no generally accepted method for SCA measurement. SCA inversely varied with liquid density and followed a power law with the air-to-liquid mass flow ratio; however, the derived expression also performed well by replacing air-to-liquid mass flow ratio by either Mach number or momentum flux ratio. A simple empirical equation was derived, which allows the estimation of SCA of airblast atomization in a wide parameter range within a 3.5% deviation. The measured results were evaluated in the light of high-speed camera images in the vicinity of the nozzle; it was found that increased liquid jet breakup length decreases SCA while intense ligament formation increases it.

Plný text v Digitální knihovně

Dokumenty

BibTex


@article{BUT164203,
  author="András {Urbán} and Bálint {Katona} and Milan {Malý} and Jan {Jedelský} and Viktor {Józsa}",
  title="Empirical correlation for spray half cone angle in plain-jet airblast atomizers",
  annote="Plain-jet airblast atomizers are widely used in industrial applications. The literature contains numerous papers on Sauter mean diameter, however, there is no estimation method available for spray cone angle, SCA, which derivation is the primary goal of this study. Four distinct, practical model liquids were analyzed: distilled water, diesel oil, light heating oil, and crude rapeseed oil. The atomizing pressure and liquid preheating temperature were varied in the range of 0.3–2.4 bar and 25–85 °C, respectively. This latter parameter enabled a wide and continuous liquid kinematic viscosity investigation range of 0.33–44.2 mm2/s. The resulting sprays were imaged at various shutter speeds for proper edge detection. An adaptive thresholding algorithm was developed in Matlab software environment to calculate SCA. The methodology is discussed in detail to facilitate the re-implementation of this technique since there is no generally accepted method for SCA measurement. SCA inversely varied with liquid density and followed a power law with the air-to-liquid mass flow ratio; however, the derived expression also performed well by replacing air-to-liquid mass flow ratio by either Mach number or momentum flux ratio. A simple empirical equation was derived, which allows the estimation of SCA of airblast atomization in a wide parameter range within a 3.5% deviation. The measured results were evaluated in the light of high-speed camera images in the vicinity of the nozzle; it was found that increased liquid jet breakup length decreases SCA while intense ligament formation increases it.",
  address="Elsevier",
  chapter="164203",
  doi="10.1016/j.fuel.2020.118197",
  howpublished="online",
  institution="Elsevier",
  number="1",
  volume="277",
  year="2020",
  month="october",
  pages="1--11",
  publisher="Elsevier",
  type="journal article in Web of Science"
}