Detail publikace

Porous Silicon & Titanium Dioxide Coatings Prepared by Atmospheric Pressure Plasma Jet Chemical Vapour Deposition Technique - A Novel Coating Technology for Photovoltaic Modules

BHATT, S. PULPYTEL, J. KRČMA, F. MAZÁNKOVÁ, V. AREFI-KHONSARI, F.

Originální název

Porous Silicon & Titanium Dioxide Coatings Prepared by Atmospheric Pressure Plasma Jet Chemical Vapour Deposition Technique - A Novel Coating Technology for Photovoltaic Modules

Anglický název

Porous Silicon & Titanium Dioxide Coatings Prepared by Atmospheric Pressure Plasma Jet Chemical Vapour Deposition Technique - A Novel Coating Technology for Photovoltaic Modules

Jazyk

en

Originální abstrakt

Atmospheric Pressure Plasma Jet (APPJ) is an alternative for wet processes used to make anti reflection coatings and smooth substrate surface for the PV module. It Is also an attractive technique because of it's high growth rate, low power consumption, lower cost and absence of high cost vacuum systems. This work deals with the deposition of silicon oxide from hexamethyldisiloxane (HMDSO) thin films and titanium dioxide from tetraisopropyl ortho titanate using an atmospheric pressure plasma jet (APPJ) system in open air conditions. A sinusoidal high voltage with a frequency between 19-23 kHz at power up to 1000 W was applied between two tubular electrodes separated by a dielectric material. The jet, characterized by Tg = 600-800K, was mostly laminar (Re = 1200) at the nozzle exit and became partially turbulent along the jet axis (Re = 3300). The spatially resolved mission spectra showed OH, N2, N2+ and CN molecular bands and O, H, N, Cu and Cr lines as well as the NO2 chemiluminescence continuum (450-800 nm). Thin films with good uniformity on the substrate were obtained at high deposition rate, between 800-1000 nm/s, and AFM results revealed that coatings are relatively smooth (Ra = 2 nm). The FTIR and SEM analyses were better used to monitor the chemical composition and the morphology of the films in function of the different experimental conditions.

Anglický abstrakt

Atmospheric Pressure Plasma Jet (APPJ) is an alternative for wet processes used to make anti reflection coatings and smooth substrate surface for the PV module. It Is also an attractive technique because of it's high growth rate, low power consumption, lower cost and absence of high cost vacuum systems. This work deals with the deposition of silicon oxide from hexamethyldisiloxane (HMDSO) thin films and titanium dioxide from tetraisopropyl ortho titanate using an atmospheric pressure plasma jet (APPJ) system in open air conditions. A sinusoidal high voltage with a frequency between 19-23 kHz at power up to 1000 W was applied between two tubular electrodes separated by a dielectric material. The jet, characterized by Tg = 600-800K, was mostly laminar (Re = 1200) at the nozzle exit and became partially turbulent along the jet axis (Re = 3300). The spatially resolved mission spectra showed OH, N2, N2+ and CN molecular bands and O, H, N, Cu and Cr lines as well as the NO2 chemiluminescence continuum (450-800 nm). Thin films with good uniformity on the substrate were obtained at high deposition rate, between 800-1000 nm/s, and AFM results revealed that coatings are relatively smooth (Ra = 2 nm). The FTIR and SEM analyses were better used to monitor the chemical composition and the morphology of the films in function of the different experimental conditions.

Dokumenty

BibTex


@article{BUT96879,
  author="František {Krčma} and Věra {Mazánková}",
  title="Porous Silicon & Titanium Dioxide Coatings Prepared by Atmospheric Pressure Plasma Jet Chemical Vapour Deposition Technique - A Novel Coating Technology for Photovoltaic Modules",
  annote="Atmospheric Pressure Plasma Jet (APPJ) is an alternative for wet processes used to make anti reflection coatings and smooth substrate surface for the PV module. It Is also an attractive technique because of it's high growth rate, low power consumption, lower cost and absence of high cost vacuum systems. This work deals with the deposition of silicon oxide from hexamethyldisiloxane (HMDSO) thin films and titanium dioxide from tetraisopropyl ortho titanate using an atmospheric pressure plasma jet (APPJ) system in open air conditions. A sinusoidal high voltage with a frequency between 19-23 kHz at power up to 1000 W was applied between two tubular electrodes separated by a dielectric material. The jet, characterized by Tg = 600-800K, was mostly laminar (Re = 1200) at the nozzle exit and became partially turbulent along the jet axis (Re = 3300). The spatially resolved mission spectra showed OH, N2, N2+ and CN molecular bands and O, H, N, Cu and Cr lines as well as the NO2 chemiluminescence continuum (450-800 nm). Thin films with good uniformity on the substrate were obtained at high deposition rate, between 800-1000 nm/s, and AFM results revealed that coatings are relatively smooth (Ra = 2 nm). The FTIR and SEM analyses were better used to monitor the chemical composition and the morphology of the films in function of the different experimental conditions.",
  chapter="96879",
  number="1",
  volume="3",
  year="2011",
  month="december",
  pages="1021--1034",
  type="journal article - other"
}